Sound level meter - Knowledge

1093:(IEC) specifications at the same time, as the ANSI standard describes instruments that are calibrated to a randomly incident wave, i.e. a diffuse sound field, while internationally meters are calibrated to a free field wave, that is sound coming from a single direction. Further, US dosimeters have an exchange rate of level against time where every 5 dB increase in level halves the permitted exposure time; whereas in the rest of the world a 3 dB increase in level halves the permitted exposure time. The 3 dB doubling method is called the "equal energy" rule and there is no possible way of converting data taken under one rule to be used under the other. Despite these differences, many developing countries refer to both US and international specifications within one instrument in their national regulations. Because of this, many commercial PSEM have dual channels with 3 and 5 dB doubling, some even having 4 dB for the U.S. Air Force. 987:

When an impulse sound is produced, the stape's annular ligament flexes and strongly clips the sound's oscillation peak. As the MIL-STD-1474 has evolved, technology and methods have improved the AHAAP's accuracy. Researchers claim that the AHAAP has been proven to be more accurate in cases of double protection but not always in unwarned impulse noise instances relative to the competitive metric LAeq8hr. Some suggestions for further development focus on creating a more user-friendly software, the placement of the microphone in data collection, the absence of the MEM reflex in populations, and the reevaluation of free-field conditions in calculations. Agencies such as NATO, the American Institute of Biological Sciences, and the National Institute for Occupational Safety and Health agreed that these suggestions be attended to before the metric is implemented. This shared conclusion was made prior to the development of MIL-STD-1474E.

971:

aircraft and aerial systems, and shipboard noise. Unless marked with warning signage, steady state and impulse noises are not to exceed 85 decibels A-weighted (dBA) and, if wearing protection, 140 decibels (dBP) respectively. It establishes acoustical noise limits and prescribes testing requirements and measurement techniques for determining conformance to the noise limits specified herein. This standard applies to the acquisition and product improvement of all designed or purchased (non-developmental items) systems, subsystems, equipment, and facilities that emit acoustic noise. This standard is intended to address noise levels emitted during the full range of typical operational conditions. This standard includes two methods for assessing the impulse noise and risk to hearing.

1182:

concluded that smartphone sound apps can serve to empower workers and help them make educated decisions about their workplace environments. Although most smartphone sound measurement apps are not accurate enough to be used for legally required measurements, the NIOSH Sound Level Meter app met the requirements of IEC 61672/ANSI S1.4 Sound Level Meter Standards (Electroacoustics - Sound Level Meters - Part 3: Periodic Tests). Calibrated microphones greatly enhances the accuracy and precision of smartphone-based noise measurements. To calibrate the sound level meter apps one must use an acoustical calibrator rather than relying on the pre-defined profiles. This study indicated that the gap between professional instruments and smartphone-based apps are narrowing.

468: 396: 477: 983:

locations.The AHAAH model calculates the estimated displacement of the basilar membrane and summates the accumulation of the flexure of the basilar membrane. The user inputs their noise exposure, protection level, and whether they were forewarned of the noise, to receive their hazard vulnerability in auditory risk units (ARU). This value can be converted to compound threshold shifts and the allowed number of exposure (ANE). Compound threshold shifts is a value that integrates both temporary and permanent shifts in auditory threshold, the latter being correlated to hair cell function.

22: 1163: 1174:, their constant network connectivity, the built-in geographic information system functionality and user-interactivity features present a great opportunity to revolutionize the way we look at noise, its measurement, and its effects on hearing and overall health. The ability to acquire and display real-time noise exposure data raises people's awareness about their work (and off-work) environment and allows them to make informed decisions about hearing hazards and overall well-being. The National Institute for Occupational Safety and Health 237:"These ANSI standards set performance and accuracy tolerances according to three levels of precision: Types 0, 1, and 2. Type 0 is used in laboratories, Type 1 is used for precision measurements in the field, and Type 2 is used for general-purpose measurements. For compliance purposes, readings with an ANSI Type 2 sound level meter and dosimeter are considered to have an accuracy of ±2 dBA, while a Type 1 instrument has an accuracy of ±1 dBA. A Type 2 meter is the minimum requirement by OSHA for 1138: 732: 561: 952:. While applying double hearing protection helps prevent auditory damage, it may compromise effectiveness by isolating the user from his or her environment. With hearing protection on, a soldier is less likely to be aware of his or her movements, alerting the enemy to their presence. Hearing protection devices (HPD) could also require higher volume levels for communication, negating their purpose. 2211: 381:, as in the sound pressure level measured through a microphone or the electronic signal level measured at the output from an audio component, such as a mixing desk. Measurement results depend on the frequency weighting (how the sound level meter responds to different sound frequencies), and time weighting (how the sound level meter reacts to changes in sound pressure with time) applied. 931:-frequency-weighting, with a general tightening of limit tolerances, as well as the inclusion of maximum allowable measurement uncertainties for each described periodic test. The periodic testing part of the standard (IEC61672.3) also requires that manufacturers provide the testing laboratory with correction factors to allow laboratory electrical and acoustic testing to better mimic 927:

were replaced by IEC 651, later renamed IEC 60651, while the linear integrating meters were initially described by IEC 804, later renamed IEC 60804. Both IEC 60651 and 60804 included four accuracy classes, called "types". In IEC 61672 these were reduced to just two accuracy classes 1 and 2. New in the standard IEC 61672 is a minimum 60 dB linear span requirement and

125:. In 1969, a group of University researchers from California founded Pulsar Instruments Inc. which became the first company to display sound exposure times on the scale of a sound level meter, as well as the sound level. This was to comply with the 1969 Walsh-Healey Act, which demanded that the noise in US workplaces should be controlled. In 1980, Britain's 569: 1110:(RT60) (a measure of the time required for the sound to "fade away" in an enclosed area after the source of the sound has stopped) measurement capabilities. Measurements can be done using the integrated impulse response or interrupted noise methods. Such sound level meters should comply with latest ISO 3382-2 and ASTM E2235-04 measurement standards. 181:

frequency-weighted noise to give sound exposure and the metric used is pressure squared times time, often Pa²·s, but Pa²·h is also used. However, because the unit of sound was historically described in decibels, the exposure is most often described in terms of sound exposure level (SEL), the logarithmic conversion of sound exposure into decibels.

1057:). If a manufacturer cannot show at least one model in his range that has such approval, it is reasonable to be wary, but the cost of this approval militates against any manufacturer having all his range approved. Inexpensive sound level meters (under $ 200) are unlikely to have a Pattern Approval and may produce incorrect measurement results. 442:

scientific grounds, it is nonetheless the legally required standard for almost all such measurements and has the huge practical advantage that old data can be compared with new measurements. It is for these reasons that A-weighting is the only weighting mandated by the international standard, the frequency weightings 'C' and 'Z' being options.

779:

is simply the highest RMS reading a conventional sound level meter gives over a stated period for a given time-weighting (S, F, or I) and can be many decibels less than the peak value. In the European Union, the maximum permitted value of the peak sound level is 140 dB(C) and this equates to 200 Pa pressure. The symbol for the

177:

obtained with a standard frequency weighting and standard time weighting. The reference pressure is set by the International agreement to be 20 micropascals for airborne sound. It follows that the decibel is, in a sense, not a unit, it is simply a dimensionless ratio; in this case the ratio of two pressures.

1150:

capabilities such as remote communication, GPS, and weather stations. These can often also be powered using solar power. Applications for such monitoring stations include airport noise, construction noise, mining noise, traffic noise, rail noise, community noise, wind farm noise, industrial noise, etc.

2459:

Komorn A, Luquet P (1979). Méthode de Description Objective D'un Environnement Acoustique: Contribution a L'elaboration D'objectifs de Qualite [Method of Objective Description of an Acoustic Environment: Contribution to the Development of Quality Objectives.] (Report) (in French). Laboratoire

1149:

Some applications require the ability to monitor noise continuously on a permanent or semi-permanent basis. Some manufacturers offer permanent and semi-permanent noise monitoring stations for this purpose. Such monitoring stations are typically based on a sound level meter at the heart and some added

1117:

is a signal generator that provides pink or white noise through an amplifier and omnidirectional speakers. In fact, the omnidirectional speaker, or sound source, should provide an equal dispersion of sound throughout the room. To achieve accurate measurements, sound should radiate evenly. This can be

970:

In 2015, MIL-STD 1474D evolved to become MIL-STD-1474E which, as of 2018, remains to be the guidelines for United States' military defense weaponry development and usage. In this standard, the Department of Defense established guidelines for steady state noise, impulse noise, aural non-detectability,

677:

has the advantage that as regulations change, old data can be re-processed to check if a new regulation is met. It also permits data to be converted from one metric to another in some cases. Today almost all fixed airport noise monitoring systems, which are in concept just complex sound level meters,

176:

The output of the RMS circuit is linear in voltage and is passed through a logarithmic circuit to give a readout linear in decibels (dB). This is 20 times the base 10 logarithm of the ratio of given root-mean-square sound pressure to the reference sound pressure. Root-mean-square sound pressure being

1060:

Even the most accurate approved sound level meter must be regularly checked for sensitivity—what most people loosely call 'calibration'. The procedures for periodic testing are defined within IEC61672.3-2013. To ensure accuracy in periodic testing, procedures should be carried out by a facility that

982:

researchers state that almost every error resulted in overcalculation of risk. By comparison, the MIL-STD-147D was deemed correct in 38% of cases with the same data. Originally developed from a cat animal model and later informed by human data, the AHAAH sums the basilar membrane displacements of 23

531:

The decision to use fast or slow is often reached by what is prescribed in a standard or a law. However, the following can be used as a guideline: The slow characteristic is mainly used in situations where the reading with the fast response fluctuates too much (more than about 4 dB) to give a

204:(British) is a specialized sound level meter intended specifically to measure the noise exposure of a person integrated over a period of time; usually to comply with Health and Safety regulations such as the Occupational Safety and Health (OSHA) 29 CFR 1910.95 Occupational Noise Exposure Standard or 113:

61672-1:2013. However, the reading from a sound level meter does not correlate well to human-perceived loudness, which is better measured by a loudness meter. Specific loudness is a compressive nonlinearity and varies at certain levels and at certain frequencies. These metrics can also be calculated

1153:

Modern monitoring stations can also offer remote communication capabilities using cellular modems, WiFi networks or direct LAN wires. Such devices allow for real-time alerts and notifications via email and text messages upon exceeding a certain dB level. Systems can also remotely email reports on a

1052:

A problem in selecting a sound level meter is "How do you know if it complies with its claimed standard?" This is a difficult question and IEC 61672 part 2 tries to answer this by the concept of "pattern approval". A manufacturer has to supply instruments to a national laboratory which tests one of

926:

Until 2003 there were separate standards for exponential and linear integrating sound level meters, but since then IEC 61672 has described both types. The classic exponential meter was originally described in IEC 123 for 'industrial' meters followed by IEC 179 for 'precision' meters. Both of these

778:

Most national regulations also call for the absolute peak value to be measured to protect workers hearing against sudden large pressure peaks, using either 'C' or 'Z' frequency weighting. 'Peak sound pressure level' should not be confused with 'MAX sound pressure level'. 'Max sound pressure level'

669:

values are taken in succession, say at 1/8 second intervals, each being stored in a digital memory. These data elements can either be transmitted to another unit or be recovered from the memory and re-constituted into almost any conventional metric long after the data has been acquired. This can be

1020:

This Test Operations Procedure (TOP) describes procedures for measuring the sound levels transmitted through air of developmental and production materiel as a means of evaluating personnel safety, speech intelligibility, security from acoustic detection and recognition, and community annoyance. It

241:

and is usually sufficient for general-purpose noise surveys. The Type 1 meter is preferred for the design of cost-effective noise controls. For unusual measurement situations, refer to the manufacturer's instructions and appropriate ANSI standards for guidance in interpreting instrument accuracy."

236:

Similarly, the American National Standards Institute (ANSI) specifies sound level meters as three different Types 0, 1 and 2. These are described, as follows, in the Occupational Safety and Health OSHA Technical Manual TED01-00-015, Chapter 5, OSHA Noise and Hearing Conservation, Appendix III:A,

232:

IEC standards divide sound level meters into two "classes". Sound level meters of the two classes have the same functionality, but different tolerances for error. Class 1 instruments have a wider frequency range and a tighter tolerance than a lower cost Class 2 unit. This applies to both the sound

1181:

Researchers reported that challenges remain with using smartphones to collect and document noise exposure data due to encounters with privacy and collection of personal data, motivation to participate in such studies, corrupted or bad data, and the ability to store the data collected. Researchers

1072:

For a simple single level and frequency check, units consisting of a computer controlled generator with additional sensors to correct for humidity, temperature, battery voltage and static pressure can be used. The output of the generator is fed to a transducer in a half-inch cavity into which the

986:

The AHAAH's claimed improvements in accuracy are often attributed to its sensitivity to the flexing of the middle ear muscle (MEM) and annular ligament of the stapes. When someone is forewarned of a sound, the MEM flexes, which is associated with reduced ability of the sound waves to reverberate.

939:

budget. This makes it unlikely that a sound level meter designed to the older 60651 and 60804 standards will meet the requirements of IEC 61672 : 2013. These 'withdrawn' standards should no longer be used, especially for any official purchasing requirements, as they have significantly poorer

215:

Traditionally, noise dosemeters were relatively large devices with a microphone mounted near the ear and having a cable going to the instrument body, itself usually belt worn. These devices had several issues, mainly the reliability of the cable and the disturbance to the user's normal work mode,

959:

The first military standard (MIL-STD) on sound was published in 1984 and underwent revision in 1997 to become MIL-STD-1474D. This standard establishes acoustical noise limits and prescribes testing requirements and measurement techniques for determining conformance to the noise limits specified

901:

The following International standards define sound level meters, PSEM and associated devices. Most countries' national standards follow these very closely, the exception being the US. In many cases the equivalent European standard, agreed by the EU, is designated for example EN 61672 and the UK

441:

In almost all countries, the use of A-weighting is mandated to be used for the protection of workers against noise-induced hearing loss. The A-weighting curve was based on the historical equal-loudness contours and while arguably A-weighting is no longer the ideal frequency weighting on purely

211:

This is normally intended to be a body-worn instrument and thus has a relaxed technical requirement, as a body-worn instrument—because of the presence of the body—has a poorer overall acoustic performance. A PSEM gives a read-out based on sound exposure, usually Pa²·h, and the older 'classic'

89:

sound pressure is applied. This is known as microphone sensitivity. The instrument needs to know the sensitivity of the particular microphone being used. Using this information, the instrument is able to accurately convert the electrical signal back to sound pressure, and display the resulting

216:

caused by the presence of the cable. In 1997 following a UK research grant an EU patent was issued for the first of a range of devices that were so small that they resembled a radiation badge and no cable was needed as the whole unit could be fitted near the ear. UK designer and manufacturer,

709:

is a very valuable method for acoustic data storage; initially, a concept of the French Government's Laboratoire National d'Essais (ref 1), it has now become the most common method of storing and displaying a true time history of the noise in professional commercial sound level meters. The

1178:) conducted a pilot study to select and characterize the functionality and accuracy of smartphone sound measurement applications (apps) as an initial step in a broader effort to determine whether these apps can be relied on to conduct participatory noise monitoring studies in the workplace. 224:, which was the world's first truly wireless noise dosimeter. Today these devices measure not only simple noise dose, but some even have four separate dosemeters, each with many of the functions of a full-sized sound level meter, including in the latest models full octave band analysis. 180:

An exponentially averaging sound level meter, which gives a snapshot of the current noise level, is of limited use for hearing damage risk measurements; an integrating or integrating-averaging meter is usually mandated. An integrating meter simply integrates—or in other words 'sums'—the

173:) originally called Fast, and 'I' (35 ms) originally called Impulse. Their names were changed in the 1980s to be the same in any language. I-time-weighting is no longer in the body of the standard because it has little real correlation with the impulsive character of noise events. 449:(SPL), but is now mandated for all levels. C-weighting is however still used in the measurement of the peak value of a noise in some legislation, but B-weighting – a halfway house between 'A' and 'C' has almost no practical use. D-weighting was designed for use in measuring 710:

alternative method, which is to generate a time history by storing and displaying samples of the exponential sound level, displays too many artifacts of the sound level meter to be as valuable and such sampled data cannot be readily combined to form an overall set of data.

1076:

For a complete sound level meter check, periodic testing outlined in IEC61672.3-2013 should be carried out. These tests excite the sound level meter across the entire frequency and dynamic range ensuring compliance with expected design goals defined in IEC61672.1-2013.

410:

much less, and has a slight boost in the mid-range, representing the sensitivity of normal human hearing at low (quiet) levels. C-Weighting, more sensitive to the lower frequencies, represents what humans hear when the sound is loud (near 100 dB SPL).

233:

level meter itself as well as the associated calibrator. Most national standards permit the use of "at least a Class 2 instrument". For many measurements, it is not necessary to use a Class 1 unit; these are best employed for research and law enforcement.

593:

Sound exposure level—in decibels—is not much used in industrial noise measurement. Instead, the time-averaged value is used. This is the time average sound level or as it is usually called the 'equivalent continuous sound level' has the formal symbol

212:

dosimeters giving the metric of 'percentage dose' are no longer used in most countries. The problem with "%dose" is that it relates to the political situation and thus any device can become obsolete if the "100%" value is changed by local laws.

713:

Until 2003 there were separate standards for exponential and linear integrating sound level meters, (IEC 60651 and IEC 60804—both now withdrawn), but since then the combined standard IEC 61672 has described both types of meter. For short

601:

as described in paragraph 3,9 "Definitions" of IEC 61672-1 where many correct formal symbols and their common abbreviations are given. These mainly follow the formal ISO acoustic definitions. However, for mainly historical reasons,

169:(RMS) circuit and thus it must have a time constant of integration; today referred to as the time-weighting. Three of these time-weightings have been internationally standardized, 'S' (1 s) originally called Slow, 'F' (125 978:(AHAAH), a one-dimensional electro-acoustic analog of the auditory system, produced MIL-STD 1474E's numerical guidelines. Over time the predictability of this algorithm has been claimed to have increased to 95% accuracy. 582:

If you look at these graphs of sound level over time, the area under the blue curve represents the energy. The horizontal red line drawn to represent the same area under the blue curve, gives us the LAeq. That is

453:

when non-bypass jets were being measured; after the demise of Concord, these are all military types. For all civil aircraft noise measurements, A-weighting is used, as is mandated by the ISO and ICAO standards.

57:

of the microphone responds to changes in air pressure caused by sound waves. That is why the instrument is sometimes referred to as a sound pressure level meter (SPL). This movement of the diaphragm, i.e. the

626:

is 10 times the base 10 logarithm of the ratio of a root-mean-square A-weighted sound pressure during a stated time interval to the reference sound pressure and there is no time constant involved. To measure

153:

The IEC 61672-1 specifies "three kinds of sound measuring instruments". They are the "conventional" sound level meter, the integrating-averaging sound level meter, and the integrating sound level meter.

1073:

sound level meter microphone is inserted. The acoustic level generated is 94 dB which is 1 pascal and is at a frequency of 1 kHz where all the frequency weightings have the same sensitivity.

514:

The graph indicates how this works. In this example, the input signal suddenly increases from 50 dB to 80 dB, stays there for 6 seconds, then drops back suddenly to the initial level.

964:) systems, subsystems, equipment, and facilities that emit acoustic noise. This standard is intended to address noise levels emitted during the full range of typical operational conditions. 590:

LAeq is not always a straight line. If the LAeq is plotted as the equivalent from the beginning of the graph to each of the measurement points, the plot is shown in the second graph.

532:

reasonably well-defined value. Modern digital displays largely overcome the problem of fluctuating analogue meters by indicating the maximum r.m.s. value for the preceding second.

1185:

Healthy Hearing, an organization dedicated to hearing health, reported on the top smartphone sound level meter apps: NIOSH Sound Level Meter, Decibel X, and Too Noisy Pro.

1520: 1053:

them and if it meets its claims issue a formal Pattern Approval certificate. In Europe, the most common approval is often considered to be that from the PTB in Germany (

524:

A fast measurement (green line) is quicker to react. It will take approximately 0.6 seconds to reach 80 dB and just under 1 second to drop back down to 50 dB.

517:

A slow measurement (yellow line) will take approximately 5 seconds (attack time) to reach 80 dB and around 6 seconds (decay time) to drop back down to 50 dB.

193:(dosimeter in American English). However, this is now formally known as a personal sound exposure meter (PSEM) and has its own international standard IEC 61252:1993. 535:

An impulse measurement (blue line) will take approximately 0.3 seconds to reach 80 dB and over 9 seconds to drop back down to 50 dB. The impulse response,

2228:

Celestina M, Hrovat J, Kardous CA (2018). "Smartphone-based sound level measurement apps: Evaluation of compliance with international sound level meter standards".

1408: 403:

The second letter indicates the frequency weighting. "Pattern approved" sound level meters typically offer noise measurements with A, C and Z frequency weighting.

1527: 1175: 356: 507:, with F = fast, S = slow, I = impulse. Time weighting is applied so that levels measured are easier to read on a sound level meter. The time weighting 1021:

covers tests for steady-state noise from military vehicles and general equipment, and impulse noise from weapon systems and explosive-ordnance materiel.

1066: 1062: 1439: 126: 634:

an integrating-averaging meter is needed; this in concept takes the sound exposure, divides it by time, and then takes the logarithm of the result.

975: 53:. The best type of microphone for sound level meters is the condenser microphone, which combines precision with stability and reliability. The 920: 1122:. All speakers should be connected in a series–parallel network, to achieve in-phase operation and impedance matching to the amplifier. 1154:

daily, weekly or monthly basis. Real-time data publication is often also desired, which can be achieved by pushing data to a website.

1090: 935:

responses. Each correction used should be provided with uncertainties, that need to be accounted for in the testing laboratory final

915:

IEC 62585 : 2012 "Electroacoustics – Methods to determine corrections to obtain the free-field response of a sound level meter"

579:= equivalent. Equivalent values are a form of time weighting that is easier to read on a display than the instantaneous sound level. 370: 110: 26: 1604: 349: 485:

Graphs of fast, slow, and impulse time weightings applied so that sound levels measured are easier to read on a sound level meter.

1355: 979: 2483: 1086: 1054: 1629: 1505: 2353: 1118:

achieved using a spherical distribution aligning 12 speakers in a so-called dodecahedral configuration, as illustrated by

699:

is a feature of most commercial integrating sound level meters—although some manufacturers give it many different names.

342: 74:). While describing sound in terms of sound pressure, a logarithmic conversion is usually applied and the sound pressure 2004: 2478:(1986 ed.). New York, N.Y.: Published by the American Institute of Physics for the Acoustical Society of America. 1312:

Kanji A, Khoza-Shangase K, Ntlhakana L (June 2019). "Noise-induced hearing loss: what South African mineworkers know".

2033: 948:

Combatants in every branch of the United States' military are at risk for auditory impairments from steady state or

919:

These International Standards were prepared by IEC technical committee 29:Electroacoustics, in cooperation with the

1119: 2380:"CDC - Noise and Hearing Loss Prevention - NIOSH Sound Level Meter App - NIOSH Workplace Safety and Health Topic" 2111:"CDC – Noise and Hearing Loss Prevention – NIOSH Sound Level Meter App – NIOSH Workplace Safety and Health Topic" 884:

ASTM E2235 (2004) Standard Test Method for Determination of Decay Rates for Use in Sound Insulation Test Methods.

764:

appear in the label, this simply represents the maximum or minimum value measured over a certain period of time.

105:

studies for the quantification of different kinds of noise, especially for industrial, environmental, mining and

539:

can be used in situations where there are sharp impulsive noises to be measured, such as fireworks or gunshots.

446: 2522: 1085:

Sound level meters are also divided into two types in "the Atlantic divide". Sound level meters meeting the US

692:

values can be transmitted via telephone lines or the Internet to a central display and processing unit. Short

2273:"Evaluation of smartphone sound measurement applications (apps) using external microphones-A follow-up study" 1785:"Analytical and numerical modeling of the hearing system: Advances towards the assessment of hearing damage" 406:

Z-weighting represents the sound pressure equally at all frequencies. A-weighting, weights lower and higher

109:. The current international standard that specifies sound level meter functionality and performances is the 1747: 1258: 1142: 1887: 2527: 960:

herein. This standard applies to the acquisition and product improvement of all designed or purchased (

2517: 221: 1905: 1978: 1285: 1236: 1204: 1199: 881:

ISO 3382-2:2008 Measurement of Room Acoustic Parameters Part 2: Reverberation Time in Ordinary Rooms

2512: 2192: 2052: 1114: 936: 395: 1480: 1575: 1194: 961: 932: 1836: 1126: 949: 909:

IEC 61252 : 1993 "Electroacoustics – specifications for personal sound exposure meters"

54: 2284: 2148: 1650: 1381: 1290: 1263: 137: 122: 2493:

Krug RW (1993). Dosimeter standards, Europe & America, what difference does it make?.

2092: 8: 842:

IEC61260 Ed. 1.0 (2014) Electroacoustics – Octave-band and fractional-octave-band filters

162: 25:

An integrating-averaging Cirrus Research's Optimus sound level meter which complies with

2288: 2152: 445:

Originally, the A-weighting was only meant for quiet sounds in the region of 40 dB

2532: 2305: 2272: 2253: 2169: 2136: 1809: 1784: 1700:. Proceedings of Meetings on Acoustics. Acoustical Society of America. p. 040005. 1698:

Military standard 1474E: Design criteria for noise limits vs. operational effectiveness

1337: 1107: 1403: 21: 2479: 2310: 2257: 2245: 2174: 1814: 1721: 1329: 1226: 832:

ANSI S1.4-2014 (a U.S. nationally adopted international standard from IEC 61672:2013)

238: 85:

A microphone is distinguishable by the voltage value produced when a known, constant

67: 1861: 1341: 2300: 2292: 2241: 2237: 2164: 2156: 1804: 1796: 1701: 1321: 1231: 438:

frequency weightings are now obsolete and are no longer described in the standard.

419: 166: 86: 2379: 2110: 1926: 1434: 1325: 1952: 1800: 1551:"IEC 61672-1:2013 Electroacoustics - Sound level meters - Part 1: Specifications" 878:

ISO 3382-1:2009 Measurement of Room Acoustic Parameters Part 1: Performance Rooms

407: 190: 102: 1635: 2537: 1209: 1125:

The reverberation-time measurements are often used to calculate wall/partition

450: 118: 106: 91: 59: 1101: 129:

introduced the world's first handheld sound level meter to provide integrated

2506: 2249: 2215: 1783:

De Paolis A, Bikson M, Nelson JT, de Ru JA, Packer M, Cardoso L (June 2017).

63: 467: 121:

sound level meter, was released in 1960 and developed by the Danish company

2314: 2178: 1955:

IEC 61672-1, Electroacoustics – Sound level meters – Part 1: Specifications

1818: 1675: 1550: 1461: 1333: 1214: 826:

IEC60651 Ed 1.2 (2001) plus Amendment 1 (1993-02) and Amendment 2 (2000–10)

205: 1888:"Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests" 476: 390: 170: 79: 1376: 1002:) computes the integrated energy and equates it to a 100 ms interval. (L 369:

Labels used to describe sound and noise level values are defined in the

1171: 1162: 50: 2296: 2160: 1706: 1137: 1012:) incorporates an adjustment for the initial duration of a blast wave. 2070: 2029: 1901: 1548: 670:

done using either dedicated programs or standard spreadsheets. Short

46: 78:

is stated instead, in decibels (dB), with 0 dB SPL equal to 20

2405: 217: 2328: 735:

Graph of an LAFmax sound level measurement calculated every minute

731: 130: 2214:

This article incorporates text from this source, which is in the

508: 95: 2354:"The best smartphone decibel meter apps to measure noise levels" 560: 542: 373:

Standard 61672-1:2013 For labels, the first letter is always an

721:

to be valuable the manufacturer must ensure that each separate

564:

Graph of LAeq sound level measurement calculated over 5 minutes

327: 311: 295: 2193:"So How Accurate Are These Smartphone Sound Measurement Apps?" 906:

IEC 61672 : 2013 "Electroacoustics – sound level meters"

685:

as their metric, as a steady stream of the digital one second

521:

is appropriate when measuring a signal that fluctuates a lot.

1530:. Occupational Health and Safety Administration. 7 March 1996 1508:. Occupational Health and Safety Administration. 3 March 2011 1089:(ANSI) specifications cannot usually meet the corresponding 912:

IEC 60942 : 2003 "Electroacoustics – sound calibrators"

2329:"Hearing aid and hearing clinic directory - Healthy Hearing" 2074: 1311: 2430: 1959:. International Electrotechnical Commission (IEC). May 2002 1314:

International Journal of Occupational Safety and Ergonomics

1102:

Building acoustics, sound insulation and reverberation time

992:

The Level Impulse Equivalent Energy for 100 milliseconds (L

511:

sudden changes in level, thus creating a smoother display.

279: 71: 49:

measurements. It is commonly a hand-held instrument with a

1782: 1506:"OSHA 29 CFR 1910.95 Occupational Noise Exposure Standard" 2431:"A Noise Level Meter built for the Classroom.| Too Noisy" 2137:"Evaluation of smartphone sound measurement applications" 1979:"Environment Noise / Noise Assessment | Brüel & Kjær" 1036: 1031: 528:

may be more suitable where the signal is less impulsive.

2465:

Wallis AD (September 1992). From Mahogany to Computers.

1047: 568: 2227: 1528:"OSHA Noise and Hearing Conservation, Appendix III:A" 1041: 1605:"fast slow impulse time weighting what do they mean" 1750:

Department of Defense Design Criteria, Noise Limits

1724:

Department of Defense Design Criteria, Noise Limits

165:signal from the microphone is converted to DC by a 1864:Test Operations Procedure:Sound Level Measurements 1837:A comparison of metrics for impulse noise exposure 1634:, Product Technology Partners Ltd., archived from 1106:Some advanced sound level meters can also include 1067:International Laboratory Accreditation Cooperation 1063:International Laboratory Accreditation Cooperation 1032:The United Kingdom professional body for acoustics 767: 572:Graph of a continuous LAeq sound level measurement 414:The IEC 61672-1:2013 mandates the inclusion of an 2075:"NoiseScout Unattended Noise Monitoring Solution" 1929:American National Standard for Sound Level Meters 1842:(Report). Defense Research and Development Canada 1830: 1828: 1778: 1776: 1774: 1772: 1120:Brüel & Kjær OmniPower Sound Source Type 4292 2504: 2277:The Journal of the Acoustical Society of America 2141:The Journal of the Acoustical Society of America 1549:International Electrotechnical Commission, IEC. 1429: 1427: 1396: 1129:or to quantify and validate building acoustics. 1080: 587:or average of the energy over the entire graph. 157:The standard sound level meter can be called an 976:Auditory Hazard Assessment Algorithm for Humans 189:A common variant of the sound level meter is a 2005:"Shhh, and Not Because the Fauna Are Sleeping" 1825: 1769: 1691: 1689: 422:in all sound level meters, and also describes 2467:Proceedings Euronoise, London. Plenary Paper. 1933:. American National Standards Institute. 2006 1424: 1037:The International Institute for Noise control 921:International Organization of Legal Metrology 902:national standard then becomes BS. EN 61672. 350: 2458: 1890:. International Electrotechnical Commission. 1132: 849: 2270: 2134: 1945: 1686: 1498: 184: 1868:. US Department of Defense. 1 January 2011 1157: 896: 862: 357: 343: 2304: 2168: 2002: 1919: 1834: 1808: 1728:. Department of Defense. 12 February 1997 1705: 1166:NIOSH sound level meter application (app) 1091:International Electrotechnical Commission 787:-time weighted maximum sound level is LAS 399:A, C and Z frequency weightings for sound 159:exponentially averaging sound level meter 1161: 1136: 730: 567: 559: 394: 101:Sound level meters are commonly used in 20: 2473: 1478: 1042:The home page of the IEC standards body 728:element fully complies with IEC 61672. 430:(zero) frequency weightings. The older 2505: 2464: 1757:. Department of Defense. 15 April 2015 1695: 1651:"Leq - LAE/SEL - When To Choose What?" 1286:"Environment Noise / Noise Assessment" 1253: 1251: 940:accuracy requirements than IEC 61672. 384: 1906:"Sample Pattern Approval Certificate" 1096: 1087:American National Standards Institute 1055:Physikalisch-Technische Bundesanstalt 1048:Pattern approval and periodic testing 943: 817: 2492: 2271:Kardous CA, Shaw PB (October 2016). 1642: 1248: 888: 556:: Equivalent continuous sound level 13: 2451: 2135:Kardous CA, Shaw PB (April 2014). 1356:"Sharpness 2 Loudness calculation" 812: 222:doseBadge personal noise dosimeter 14: 2549: 2069: 2051:Ltd, Acoustic Research Labs Pty. 2028: 1900: 1462:"IEC 61672-1:2013 – IEC Webstore" 1061:can produce results traceable to 872: 836: 457: 143: 2406:"Decibel X: Pro dBA Noise Meter" 2209: 2093:"Acoustic Research Labs Pty Ltd" 2053:"Acoustic Research Labs Pty Ltd" 2003:Barringer F (21 February 2011). 1648: 1576:"The Top 10 posts from our blog" 1025: 795:-frequency weighted peak it is 739: 648:An important variant of overall 475: 466: 321:Level Z-weighted impulse maximum 117:The world's first hand-held and 16:Device for acoustic measurements 2423: 2398: 2372: 2346: 2321: 2264: 2221: 2185: 2128: 2103: 2085: 2063: 2050: 2044: 2022: 1996: 1971: 1894: 1880: 1854: 1740: 1714: 1676:"IEC 62585:2012 – IEC Webstore" 1668: 1622: 1597: 1568: 1542: 1377:"History - Sound and Vibration" 245: 114:in a number of different ways. 2242:10.1016/j.apacoust.2018.04.011 1472: 1454: 1369: 1348: 1305: 1278: 1259:"What Is A Sound Level Meter?" 1: 2199:. Centers for Disease Control 1835:Nakashima A (November 2015). 1326:10.1080/10803548.2017.1412122 1242: 1081:ANSI/IEC: the Atlantic divide 893:IEC61010-1 Ed. 2.0 (2001–02) 305:Level C-weighted slow minimum 289:Level A-weighted fast maximum 1801:10.1016/j.heares.2017.01.015 1481:"What is Sound Level Meter?" 1143:Muir Woods National Monument 1141:Noise monitoring station at 637: 609:is commonly referred to as 273:Level A-weighted equivalent 7: 2097:www.acousticresearch.com.au 2057:www.acousticresearch.com.au 1188: 1113:Required for measuring the 980:US Army Research Laboratory 774:: peak sound pressure level 10: 2554: 2034:"Noise Monitoring Station" 1631:Noise Measurement Briefing 855:IEC61252 Ed. 1.1 (2002–03) 388: 253:Sound level label examples 227: 39:sound pressure level meter 1237:Health effects from noise 1205:Audio system measurements 1200:ITU-R 468 noise weighting 1133:Noise monitoring stations 850:Personal noise dosimeters 338: 333: 317: 301: 285: 269: 257: 252: 1479:rebecca (5 March 2019). 185:Personal noise dosimeter 148: 66:), is converted into an 1363:Psychoacoustic Analyses 1158:Smartphone applications 962:non-developmental items 937:Measurement uncertainty 897:International standards 863:Measurement microphones 845:ANSI S1.11-2004 (R2009) 823:IEC61672 Ed. 2.0 (2013) 491:If the third letter is 1409:Pulsar Instruments Plc 1365:. HEAD acoustics GmbH. 1195:Equal-loudness contour 1167: 1146: 1115:acoustics in buildings 933:Free field (acoustics) 858:ANSI S1.25-1991(R2007) 736: 573: 565: 503:, this represents the 400: 30: 2523:Measuring instruments 1585:. Cirrus Research PLC 1165: 1140: 868:IEC 61094 : 2000 734: 571: 563: 398: 24: 585:the equivalent value 447:sound pressure level 140:(SEL) measurements. 138:sound exposure level 92:sound pressure level 2474:Beranek LL (1986). 2289:2016ASAJ..140L.327K 2153:2014ASAJ..135L.186K 662:" where very short 385:Frequency weighting 2528:Sound measurements 2460:National d'Essais. 2360:. 26 November 2014 2283:(4): EL327–EL333. 2197:NIOSH Science Blog 2079:www.noisescout.com 2009:The New York Times 1696:Amrein BE (2015). 1412:. 13 November 2021 1168: 1147: 1108:reverberation time 1097:Other applications 944:Military standards 829:IEC60804 (2000–10) 818:Sound level meters 737: 574: 566: 401: 377:. This stands for 239:noise measurements 31: 2518:Audio engineering 2485:978-0-88318-494-3 2297:10.1121/1.4964639 2230:Applied Acoustics 2161:10.1121/1.4865269 2038:www.nti-audio.com 1913:www.nti-audio.com 1707:10.1121/2.0000207 1227:Noise measurement 1065:, or other local 367: 366: 220:, introduced the 68:electrical signal 35:sound level meter 2545: 2498: 2489: 2470: 2461: 2446: 2445: 2443: 2441: 2427: 2421: 2420: 2418: 2416: 2402: 2396: 2395: 2393: 2391: 2386:. 5 October 2018 2376: 2370: 2369: 2367: 2365: 2350: 2344: 2343: 2341: 2339: 2325: 2319: 2318: 2308: 2268: 2262: 2261: 2225: 2219: 2213: 2212: 2208: 2206: 2204: 2189: 2183: 2182: 2172: 2132: 2126: 2125: 2123: 2121: 2107: 2101: 2100: 2089: 2083: 2082: 2067: 2061: 2060: 2048: 2042: 2041: 2026: 2020: 2019: 2017: 2015: 2000: 1994: 1993: 1991: 1989: 1975: 1969: 1968: 1966: 1964: 1949: 1943: 1942: 1940: 1938: 1923: 1917: 1916: 1910: 1898: 1892: 1891: 1884: 1878: 1877: 1875: 1873: 1858: 1852: 1851: 1849: 1847: 1841: 1832: 1823: 1822: 1812: 1789:Hearing Research 1780: 1767: 1766: 1764: 1762: 1756: 1744: 1738: 1737: 1735: 1733: 1718: 1712: 1711: 1709: 1693: 1684: 1683: 1672: 1666: 1665: 1663: 1661: 1655:Brüel & Kjær 1646: 1640: 1639: 1626: 1620: 1619: 1617: 1615: 1601: 1595: 1594: 1592: 1590: 1580: 1572: 1566: 1565: 1563: 1561: 1546: 1540: 1539: 1537: 1535: 1524: 1518: 1517: 1515: 1513: 1502: 1496: 1495: 1493: 1491: 1476: 1470: 1469: 1458: 1452: 1451: 1449: 1447: 1431: 1422: 1421: 1419: 1417: 1400: 1394: 1393: 1391: 1389: 1382:Brüel & Kjær 1373: 1367: 1366: 1360: 1352: 1346: 1345: 1309: 1303: 1302: 1300: 1298: 1291:Brüel & Kjær 1282: 1276: 1275: 1273: 1271: 1264:Brüel & Kjær 1255: 1232:Noise regulation 1170:The ubiquity of 1127:sound insulation 889:Equipment safety 479: 470: 420:weighting filter 359: 352: 345: 326: 320: 310: 304: 294: 288: 278: 272: 250: 249: 167:root-mean-square 123:Brüel & Kjær 87:root mean square 2553: 2552: 2548: 2547: 2546: 2544: 2543: 2542: 2513:Noise pollution 2503: 2502: 2501: 2486: 2454: 2452:Further reading 2449: 2439: 2437: 2435:toonoisyapp.com 2429: 2428: 2424: 2414: 2412: 2404: 2403: 2399: 2389: 2387: 2378: 2377: 2373: 2363: 2361: 2358:Healthy Hearing 2352: 2351: 2347: 2337: 2335: 2333:Healthy Hearing 2327: 2326: 2322: 2269: 2265: 2226: 2222: 2210: 2202: 2200: 2191: 2190: 2186: 2147:(4): EL186-92. 2133: 2129: 2119: 2117: 2109: 2108: 2104: 2091: 2090: 2086: 2068: 2064: 2049: 2045: 2027: 2023: 2013: 2011: 2001: 1997: 1987: 1985: 1977: 1976: 1972: 1962: 1960: 1951: 1950: 1946: 1936: 1934: 1925: 1924: 1920: 1908: 1899: 1895: 1886: 1885: 1881: 1871: 1869: 1860: 1859: 1855: 1845: 1843: 1839: 1833: 1826: 1781: 1770: 1760: 1758: 1754: 1746: 1745: 1741: 1731: 1729: 1720: 1719: 1715: 1694: 1687: 1680:webstore.iec.ch 1674: 1673: 1669: 1659: 1657: 1647: 1643: 1638:on 30 June 2008 1628: 1627: 1623: 1613: 1611: 1603: 1602: 1598: 1588: 1586: 1578: 1574: 1573: 1569: 1559: 1557: 1547: 1543: 1533: 1531: 1526: 1525: 1521: 1511: 1509: 1504: 1503: 1499: 1489: 1487: 1477: 1473: 1466:webstore.iec.ch 1460: 1459: 1455: 1445: 1443: 1440:Cirrus Research 1433: 1432: 1425: 1415: 1413: 1402: 1401: 1397: 1387: 1385: 1375: 1374: 1370: 1358: 1354: 1353: 1349: 1310: 1306: 1296: 1294: 1284: 1283: 1279: 1269: 1267: 1257: 1256: 1249: 1245: 1191: 1160: 1135: 1104: 1099: 1083: 1050: 1028: 1011: 1001: 946: 899: 891: 875: 865: 852: 839: 820: 815: 813:Standardization 807: 801: 790: 783:-frequency and 776: 773: 754: 752: 745: 727: 720: 708: 698: 691: 684: 676: 668: 661: 653: 646: 644: 632: 624: 615: 607: 599: 558: 555: 547: 489: 488: 487: 486: 482: 481: 480: 472: 471: 460: 393: 387: 363: 334: 324: 318: 308: 302: 292: 286: 276: 270: 265: 260: 248: 230: 218:Cirrus Research 202:noise dosemeter 198:noise dosimeter 191:noise dosemeter 187: 151: 146: 134: 127:Cirrus Research 103:noise pollution 45:)) is used for 17: 12: 11: 5: 2551: 2541: 2540: 2535: 2530: 2525: 2520: 2515: 2500: 2499: 2490: 2484: 2471: 2462: 2455: 2453: 2450: 2448: 2447: 2422: 2397: 2371: 2345: 2320: 2263: 2220: 2184: 2127: 2102: 2084: 2062: 2043: 2021: 1995: 1970: 1944: 1918: 1893: 1879: 1853: 1824: 1768: 1739: 1713: 1685: 1667: 1641: 1621: 1596: 1567: 1541: 1519: 1497: 1471: 1453: 1423: 1395: 1368: 1347: 1320:(2): 305–310. 1304: 1277: 1246: 1244: 1241: 1240: 1239: 1234: 1229: 1218: 1217: 1212: 1210:Sound pressure 1207: 1202: 1197: 1190: 1187: 1159: 1156: 1134: 1131: 1103: 1100: 1098: 1095: 1082: 1079: 1049: 1046: 1045: 1044: 1039: 1034: 1027: 1024: 1023: 1022: 1015: 1014: 1013: 1003: 993: 990: 989: 988: 965: 950:impulse noises 945: 942: 917: 916: 913: 910: 907: 898: 895: 890: 887: 886: 885: 882: 879: 874: 873:Room acoustics 871: 870: 869: 864: 861: 860: 859: 856: 851: 848: 847: 846: 843: 838: 837:Octave filters 835: 834: 833: 830: 827: 824: 819: 816: 814: 811: 805: 799: 788: 775: 771: 766: 753: 750: 743: 738: 725: 718: 706: 696: 689: 682: 674: 666: 659: 651: 645: 642: 636: 630: 622: 613: 605: 597: 557: 553: 545: 541: 505:time weighting 484: 483: 474: 473: 465: 464: 463: 462: 461: 459: 458:Time weighting 456: 451:aircraft noise 389:Main article: 386: 383: 365: 364: 362: 361: 354: 347: 339: 336: 335: 331: 330: 322: 315: 314: 306: 299: 298: 290: 283: 282: 274: 267: 266: 263: 261: 258: 255: 254: 247: 244: 229: 226: 200:(American) or 186: 183: 150: 147: 145: 144:Classification 142: 132: 119:transistorized 107:aircraft noise 60:sound pressure 15: 9: 6: 4: 3: 2: 2550: 2539: 2536: 2534: 2531: 2529: 2526: 2524: 2521: 2519: 2516: 2514: 2511: 2510: 2508: 2496: 2491: 2487: 2481: 2477: 2472: 2468: 2463: 2457: 2456: 2436: 2432: 2426: 2411: 2407: 2401: 2385: 2381: 2375: 2359: 2355: 2349: 2334: 2330: 2324: 2316: 2312: 2307: 2302: 2298: 2294: 2290: 2286: 2282: 2278: 2274: 2267: 2259: 2255: 2251: 2247: 2243: 2239: 2235: 2231: 2224: 2217: 2216:public domain 2198: 2194: 2188: 2180: 2176: 2171: 2166: 2162: 2158: 2154: 2150: 2146: 2142: 2138: 2131: 2116: 2112: 2106: 2098: 2094: 2088: 2080: 2076: 2072: 2066: 2058: 2054: 2047: 2039: 2035: 2031: 2025: 2010: 2006: 1999: 1984: 1980: 1974: 1958: 1956: 1948: 1932: 1930: 1922: 1914: 1907: 1903: 1897: 1889: 1883: 1867: 1865: 1857: 1838: 1831: 1829: 1820: 1816: 1811: 1806: 1802: 1798: 1794: 1790: 1786: 1779: 1777: 1775: 1773: 1753: 1751: 1743: 1727: 1725: 1717: 1708: 1703: 1699: 1692: 1690: 1681: 1677: 1671: 1656: 1652: 1649:Kjær, Brüel. 1645: 1637: 1633: 1632: 1625: 1610: 1606: 1600: 1584: 1577: 1571: 1556: 1552: 1545: 1529: 1523: 1507: 1501: 1486: 1482: 1475: 1467: 1463: 1457: 1442: 1441: 1436: 1435:"Our History" 1430: 1428: 1411: 1410: 1405: 1404:"Our History" 1399: 1384: 1383: 1378: 1372: 1364: 1357: 1351: 1343: 1339: 1335: 1331: 1327: 1323: 1319: 1315: 1308: 1293: 1292: 1287: 1281: 1266: 1265: 1260: 1254: 1252: 1247: 1238: 1235: 1233: 1230: 1228: 1225: 1224: 1223: 1222: 1216: 1213: 1211: 1208: 1206: 1203: 1201: 1198: 1196: 1193: 1192: 1186: 1183: 1179: 1177: 1173: 1164: 1155: 1151: 1145:in California 1144: 1139: 1130: 1128: 1123: 1121: 1116: 1111: 1109: 1094: 1092: 1088: 1078: 1074: 1070: 1069:signatories. 1068: 1064: 1058: 1056: 1043: 1040: 1038: 1035: 1033: 1030: 1029: 1026:Organizations 1019: 1016: 1010: 1006: 1000: 996: 991: 985: 984: 981: 977: 973: 972: 969: 968:MIL-STD 1474E 966: 963: 958: 957:MIL-STD 1474D 955: 954: 953: 951: 941: 938: 934: 930: 924: 922: 914: 911: 908: 905: 904: 903: 894: 883: 880: 877: 876: 867: 866: 857: 854: 853: 844: 841: 840: 831: 828: 825: 822: 821: 810: 808: 798: 794: 786: 782: 770: 765: 763: 759: 756:If the words 749: 742: 733: 729: 724: 717: 711: 705: 700: 695: 688: 681: 673: 665: 658: 654: 641: 635: 633: 625: 617: 612: 608: 600: 591: 588: 586: 580: 578: 570: 562: 552: 548: 540: 538: 533: 529: 527: 522: 520: 515: 512: 510: 506: 502: 498: 494: 478: 469: 455: 452: 448: 443: 439: 437: 433: 429: 425: 421: 417: 412: 409: 404: 397: 392: 382: 380: 376: 372: 360: 355: 353: 348: 346: 341: 340: 337: 332: 329: 323: 316: 313: 307: 300: 297: 291: 284: 281: 275: 268: 262: 256: 251: 243: 240: 234: 225: 223: 219: 213: 209: 207: 203: 199: 194: 192: 182: 178: 174: 172: 168: 164: 160: 155: 141: 139: 135: 128: 124: 120: 115: 112: 108: 104: 99: 97: 93: 88: 83: 81: 77: 73: 69: 65: 61: 56: 52: 48: 44: 40: 37:(also called 36: 28: 23: 19: 2494: 2475: 2466: 2438:. Retrieved 2434: 2425: 2413:. Retrieved 2409: 2400: 2388:. Retrieved 2383: 2374: 2362:. Retrieved 2357: 2348: 2336:. Retrieved 2332: 2323: 2280: 2276: 2266: 2233: 2229: 2223: 2201:. Retrieved 2196: 2187: 2144: 2140: 2130: 2118:. Retrieved 2114: 2105: 2096: 2087: 2078: 2065: 2056: 2046: 2037: 2024: 2012:. Retrieved 2008: 1998: 1986:. Retrieved 1983:www.bksv.com 1982: 1973: 1961:. Retrieved 1954: 1947: 1935:. Retrieved 1928: 1921: 1912: 1896: 1882: 1872:18 September 1870:. Retrieved 1863: 1856: 1844:. Retrieved 1792: 1788: 1759:. Retrieved 1749: 1742: 1732:18 September 1730:. Retrieved 1723: 1716: 1697: 1679: 1670: 1658:. Retrieved 1654: 1644: 1636:the original 1630: 1624: 1612:. Retrieved 1608: 1599: 1587:. Retrieved 1583:cms.esi.info 1582: 1570: 1558:. Retrieved 1554: 1544: 1532:. Retrieved 1522: 1512:10 September 1510:. Retrieved 1500: 1488:. Retrieved 1485:Scarlet Tech 1484: 1474: 1465: 1456: 1444:. Retrieved 1438: 1414:. Retrieved 1407: 1398: 1386:. Retrieved 1380: 1371: 1362: 1350: 1317: 1313: 1307: 1295:. Retrieved 1289: 1280: 1268:. Retrieved 1262: 1220: 1219: 1215:Clap-o-meter 1184: 1180: 1169: 1152: 1148: 1124: 1112: 1105: 1084: 1075: 1071: 1059: 1051: 1018:TOP-1-2-608A 1017: 1008: 1004: 998: 994: 967: 956: 947: 928: 925: 918: 900: 892: 803: 796: 792: 784: 780: 777: 768: 761: 757: 755: 747: 740: 722: 715: 712: 703: 701: 693: 686: 679: 671: 663: 656: 649: 647: 639: 628: 620: 618: 610: 603: 595: 592: 589: 584: 581: 576: 575: 550: 543: 536: 534: 530: 525: 523: 518: 516: 513: 504: 500: 496: 492: 490: 444: 440: 435: 431: 427: 423: 415: 413: 405: 402: 378: 374: 368: 246:Measurements 235: 231: 214: 210: 208:2003–10/EC. 206:EU Directive 201: 197: 195: 188: 179: 175: 158: 156: 152: 116: 100: 84: 80:micropascals 75: 42: 38: 34: 32: 29:61672-1:2002 18: 2384:www.cdc.gov 2236:: 119–128. 2115:www.cdc.gov 1795:: 111–128. 1446:24 February 1388:24 February 1297:24 February 1270:24 February 1172:smartphones 791:. For the 408:frequencies 391:A-weighting 259:Description 96:decibel, dB 2507:Categories 2495:Proc AIHCE 2440:4 December 2415:4 December 2410:skypaw.com 2390:4 December 2364:4 December 2338:4 December 2203:30 January 2120:30 January 2071:Audio, NTi 2030:Audio, NTi 1902:Audio, NTi 1490:25 October 1243:References 678:use short 655:is "short 619:Formally, 64:pascal, Pa 51:microphone 2533:Acoustics 2497:(Report). 2476:Acoustics 2469:(Report). 2258:116822722 2250:0003-682X 1609:NTi Audio 55:diaphragm 2315:27794313 2179:25236152 2014:2 August 1963:29 April 1937:29 April 1819:28161584 1761:3 August 1660:25 April 1614:16 March 1589:13 March 1560:16 March 1342:46754344 1334:29214904 1221:General: 1189:See also 923:(OIML). 47:acoustic 2306:5102154 2285:Bibcode 2170:4659422 2149:Bibcode 1810:7000179 1534:9 April 1416:7 March 228:Classes 161:as the 72:volt, V 2482: 2313: 2303: 2256: 2248: 2177: 2167: 1988:19 May 1846:3 July 1817: 1807: 1555:iec.ch 1340: 1332: 1176:(NIOSH 806:C,peak 702:Short 638:Short 328:LZImax 325: 319: 312:LCSmin 309: 303: 296:LAFmax 293: 287: 277: 271: 94:(unit 70:(unit 62:(unit 2538:Sound 2254:S2CID 1909:(PDF) 1840:(PDF) 1755:(PDF) 1579:(PDF) 1359:(PDF) 1338:S2CID 509:damps 379:Level 264:Label 149:Types 76:level 2480:ISBN 2442:2018 2417:2018 2392:2018 2366:2018 2340:2018 2311:PMID 2246:ISSN 2205:2017 2175:PMID 2122:2017 2016:2014 1990:2021 1965:2013 1939:2013 1874:2012 1848:2018 1815:PMID 1763:2018 1734:2012 1662:2021 1616:2018 1591:2021 1562:2018 1536:2013 1514:2012 1492:2022 1448:2021 1418:2022 1390:2021 1330:PMID 1299:2021 1272:2021 1005:IAeq 995:IAeq 974:The 746:and 434:and 426:and 280:LAeq 136:and 2301:PMC 2293:doi 2281:140 2238:doi 2234:139 2165:PMC 2157:doi 2145:135 1805:PMC 1797:doi 1793:349 1702:doi 1322:doi 1007:100 997:100 802:or 789:max 762:min 760:or 758:max 751:min 744:max 549:or 499:or 371:IEC 111:IEC 98:). 43:SPL 27:IEC 2509:: 2433:. 2408:. 2382:. 2356:. 2331:. 2309:. 2299:. 2291:. 2279:. 2275:. 2252:. 2244:. 2232:. 2195:. 2173:. 2163:. 2155:. 2143:. 2139:. 2113:. 2095:. 2077:. 2073:. 2055:. 2036:. 2032:. 2007:. 1981:. 1911:. 1904:. 1827:^ 1813:. 1803:. 1791:. 1787:. 1771:^ 1688:^ 1678:. 1653:. 1607:. 1581:. 1553:. 1483:. 1464:. 1437:. 1426:^ 1406:. 1379:. 1361:. 1336:. 1328:. 1318:25 1316:. 1288:. 1261:. 1250:^ 1009:ms 999:ms 809:. 800:pk 797:LC 772:pk 769:LC 726:eq 719:eq 707:eq 697:eq 690:eq 683:eq 675:eq 667:eq 660:eq 652:AT 643:eq 631:AT 623:AT 616:. 614:eq 606:AT 598:AT 577:eq 554:eq 546:AT 495:, 196:A 171:ms 163:AC 133:eq 82:. 33:A 2488:. 2444:. 2419:. 2394:. 2368:. 2342:. 2317:. 2295:: 2287:: 2260:. 2240:: 2218:. 2207:. 2181:. 2159:: 2151:: 2124:. 2099:. 2081:. 2059:. 2040:. 2018:. 1992:. 1967:. 1957:" 1953:" 1941:. 1931:" 1927:" 1915:. 1876:. 1866:" 1862:" 1850:. 1821:. 1799:: 1765:. 1752:" 1748:" 1736:. 1726:" 1722:" 1710:. 1704:: 1682:. 1664:. 1618:. 1593:. 1564:. 1538:. 1516:. 1494:. 1468:. 1450:. 1420:. 1392:. 1344:. 1324:: 1301:. 1274:. 929:Z 804:L 793:C 785:S 781:A 748:L 741:L 723:L 716:L 704:L 694:L 687:L 680:L 672:L 664:L 657:L 650:L 640:L 629:L 621:L 611:L 604:L 596:L 551:L 544:L 537:I 526:F 519:S 501:I 497:S 493:F 436:D 432:B 428:Z 424:C 418:- 416:A 375:L 358:e 351:t 344:v 131:L 41:(

Text is available under the Creative Commons Attribution-ShareAlike License. Additional terms may apply.

Index